What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Texas_Gladiator]

sitting here, waiting on FedEx to drop off my daystar 1.5 spacers.... hoping they get here in enough time to install before my wife gets home from work!

Post some pics before/after! My Daystar 2" kit gets here Monday. That and 35" Ridge Grapplers go on Tuesday...

Sponsored

 

[Bobh62000]

just put my first jeep Honor Badge today and got my Off-Road sticker for Texas as well.

 

[Joker4L]

Just finished installing my Injen 5005C CAI . Also took some pics of the exhaust

 

[G8R]

Winch installed. Zeon 10. Steel cable for now. Would have gone synthetic but could not wait for backorder as I needed it installed now in preparations for a 2 week trip in 14 days. This was actually a pain in the ass to install. The Winch did not fit as the housing is too wide for the space between the bumper mount flanges. Not due to the bumper but due to the Gladiator's bumper mount flange. This bumper does not use the center top holes to mount, luckily. I had to grind off a half inch of steel from both mount flanges to get this winch to set on the mounting plate. I scratched the crap out of the sides of the winch due to fit testing and trying to get it in but there was no way without grinding. But now it is set and seems to work fine.

 

[G8R]

Also of note is that this setup dropped the front of the jeep 1/2" measured at the front of the rock rails.

 

[MaximusDecimusMeridius]

Finished up installing the 4.5 skyjacker lift. I tried to get it aligned but my local shop says there computer can't do it with the current firmware. Guess i will have to take it an hour to the dealer

 

[primethios]

Finished up installing the 4.5 skyjacker lift. I tried to get it aligned but my local shop says there computer can't do it with the current firmware. Guess i will have to take it an hour to the dealer

WOW! That looks great to me

 

[TheSolarWizard]

Finished up installing the 4.5 skyjacker lift. I tried to get it aligned but my local shop says there computer can't do it with the current firmware. Guess i will have to take it an hour to the dealer

Congrats on having solar in IL

 

[MaximusDecimusMeridius]

Congrats on having solar in IL

Lol...we live out in the sticks and used to have propane to heat with...spent anywhere from 5-8k a year on electric/propane. Our furnace went out a few years back and decided to switch to geothermal and then got solar a year later. With all the rebates going on at the time it seemed like a good time to do it...now we spend 1k or less a year on electric.

 

[JT614]

It's been a while since I did anything. Decided to lose some blue on the grille and ended up plasti-dipping the entire grille black, including the inserts. I almost like it better.

 

[TheSolarWizard]

Lol...we live out in the sticks and used to have propane to heat with...spent anywhere from 5-8k a year on electric/propane. Our furnace went out a few years back and decided to switch to geothermal and then got solar a year later. With all the rebates going on at the time it seemed like a good time to do it...now we spend 1k or less a year on electric.

It’s our hottest market right now. Smart decision

 

[sass JT]

Added some jewelry to the “red queen”... on board air. DV8 bracket, arb twin compressor, braided air line, a left over cb mount bracket and a air coupler.

 

[DirtyD]

FedEx dropped off my spacers, and I discovered my jack stands are too short to get enough axle drop. Picking up some new stands tomorrow, but probably be at least a week before I get enough time to put her up in the air again.

 

[OVERLORD]

New buggy to me, some easy stuff, some hood decals.

 

[TheSolarWizard]

Added some jewelry to the “red queen”... on board air. DV8 bracket, arb twin compressor, braided air line, a left over cb mount bracket and a air coupler.

Where did you source the bracket? Looks awesome

Sponsored