What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Lynn_F]

39s baby...

Looks great! What size lift are you running?

Sponsored

 

[JP1]

Looks great! What size lift are you running?

just a MOPAR 2"

 

[sgtkersh]

Lots done today. Front and rear bumpers, Synergy springs up front to remove the rake, JKS sway bar disconnects, Falcon shocks, Falcon adjustable steering stabilizer, and a Smittybilt winch. I just need to figure a relocation for the winch control box and all is good.

 

[MarineHawk]

Lots done today. Front and rear bumpers, Synergy springs up front to remove the rake, JKS sway bar disconnects, Falcon shocks, Falcon adjustable steering stabilizer, and a Smittybilt winch. I just need to figure a relocation for the winch control box and all is good.

Like the plates!

 

[kosmos]

In preparation for a winch I Added a Factor 55 Hawse Fairlead along with a removable front plate holder by Warrior products.

I Will figure out which winch and plate later - but the winch will have synthetic rope.
If you removed the front factory plate holder from the factory metal bumper it can be reused as a cover/spacer to cover up the various holes on the stock bumper and give you a clean looking finish. An easy mod with just a couple of holes drilled out - use the stock front bumper to mark holes with a marker and drill our with a large stepper bit.

Warrior Products Front License Plate Holder​

Factor 55 Hawse Fairlead 1.0



Factor 55 Hawse



Quick Release Warrior Products Front Plate Holder

​

 

[Rulf]

Installed the winch today

 

[salsadoc]

installed vision x reverse backup lights and wired them to the aux switches. these are amazingly bright!

 

[Gregbj33]

Over the last few days. Oculus Headlights and LED tails. Love them both!

 

[ColoradoGlad]

Over the last few days. Oculus Headlights and LED tails. Love them both!

Greg, Nice! First swap to rear LED tail lights I have seen...
Were the rear tail lights plug and play?
I'm guessing you had to program for LED...
I take you didn't have the sensors on your original tail lights? Do they do anything?

I haven't priced the rear tail lights, but I'm guessing around $500 to $600 for the pair?

 

[Gregbj33]

Greg, Nice! First swap to rear LED tail lights I have seen...
Were the rear tail lights plug and play?
I'm guessing you had to program for LED...
I take you didn't have the sensors on your original tail lights? Do they do anything?

I haven't priced the rear tail lights, but I'm guessing around $500 to $600 for the pair?

They were plug and play but I do have the Tazer so I set the tails to LED through that. Not sure if they would hyperlfash without the Tazer. I didn’t have the sensors nor do the new ones. Cost me $500 shipped from BAM warehouse, took about a week to get.

 

[kosmos]

Added some more creature comforts - CMM-Offroad 1" Grab Bar Ball Mount for RAM mounts. Luck I had an 8mm hex key for the 8mm dash bolt. This is a perfect machined part and the install is quick and easy - very functional with the X-Grip and arms from RAM Mounts I can add iPads, extra iPhones, HAM radio heads etc.

CMM-Offroad Grab Bar Ball Mount



CMM-Offroad Grab Bar Ball Mount
​

Also got the M.O.R.E Dead Pedal Installed.

M.O.R.E Dead Pedal

​

 

[ColoradoGlad]

They were plug and play but I do have the Tazer so I set the tails to LED through that. Not sure if they would hyperlfash without the Tazer. I didn’t have the sensors nor do the new ones. Cost me $500 shipped from BAM warehouse, took about a week to get.

I have an OBL Jscan that will change the parameters, so I should be good there..
I didn't/never really check if you could get the LED tail lights without the sensors.... Good to know! Thanks...
I'm still @issed we can't get LED lights option on the Sport or Sport S models...
It's ridicules they force you into the Overland, Rubicon or North Edition to get some of the options...
Done ranting.... smile.

Thanks again for the info...

 

[kabinski]

Here’s my solution for quick and easy storage of the freedom panels. I’m not a fan of the storage bag, so here’s what I did instead. I installed the bedrug a while back and figured out the freedom panels fit perfectly in the bed, side by side. Today I bought carpeted mats from Lowe’s (2-pack for $12), trimmed and cut them to fit the areas shown and used 3M exterior mounting tape to stick them to the surface. The back of the mats had a bit of oily residue, so I used an adhesive spray to help them stick to the tape, which worked great. The inside edge of the drivers side panel goes right against the carpeted mat up front. The rubber molding of the passenger side panel butts up against the outer edge of the drivers side panel. The outer edge of the passenger side panel makes contact with the bedrug on the inside of the tailgate once closed. It’s a perfect fit.

 

[Dorbritz]

Made some bracket and added some utility lights.

 

[ThatStinging_Jeep]

Unpackaged and prepped this bad boy today (mounted lights, grommets, etc, the tedious stuff). Hoping to pull off the stock plastic rear bumper and get this installed/wired up on Sunday when the weather finally breaks. I'll install the winch at a later time when funds allow.

whats the brand of that bumper,i like it

Sponsored