What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Willys2Gladiator]

Ha. I had to look twice as well ......buttttttt ??

I'm sorry. Still lost. What did you install? For us slow folks please.

Sponsored

 

[JTBurns]

Covered!

 

[Dewyaw]

My wonderful wife got me a fox steering stabilizer for valentine's day. Quick install and drive around the country. Very nice. Steering is nice and tight. Recommended inexpensive upgrade.

Wait a minute...I ordered mine on Black Friday and have yet to get it....??‍

 

[eyekode]

Rebel Off-Road rear bumper and bed sliders.

Man I love the look of that bumper! Then when I googled it and saw the price I realized why it looks so good

 

[Raton Pass]

Used a Matco fuel injector cleaner with stand alone small gas tank.
Put gas & BG FI cleaner in, killed the Jeeps fuel pump and started the process.
Turned the machines fuel pressure down until it limped. When it would smooth out I lowered the fuel pressure again & again.
The BG distribution outlet’s salesman tried for almost two years to find out why my washes were better than other shops.
Our old TV commercials showed my mom in her STS before & after boiling the hides.
BG sells a great decloaking spray that you can invert the can.
Cleans Mass air flow sensors & the small hole on the butterfly along with upstream & downstream 02 sensors.

If you do this, do it BEFORE you change the oil.
Plus change the oil right after you are done as a carbon filled oil pan causes etching.

If done this way you don’t even need to add BG’s 44k tank additive.

Seen new oil look old after the process.

Conical injector pattern without breaks pushes the piston evenly.

Sea Foam is #2

I am changing the oil & filter at 1000 miles tomorrow for break in.

Sold out in 2000 so I only work on my own now.?

 

[Veloruche]

Did you need a trim tool? Im about to do mine

I have one but it’s not need to remove or reinstall the footwell trim. The real issue is where you’re pulling from. It’s more pull in along the floor toward the center. I’ve highlighted the photo below where the clips are locate ( they look like the letter C and hold the trim with a round tab.

 

[Dewyaw]

I put down the Hotheads Sound Assassin on the floorboard. I still have enough that later I will take the rear seats out and do the back wall.

Please report back on any differences you notice. Nice job...

 

[TexasTJ]

Man I love the look of that bumper! Then when I googled it and saw the price I realized why it looks so good

Agreed, but I caught it on a Black Friday sale and bare steel so it was a little cheaper. Plus I sold my Rubi steel rear bumper to offset a bit.

 

[eyekode]

Used a Matco fuel injector cleaner with stand alone small gas tank.
Put gas & BG FI cleaner in, killed the Jeeps fuel pump and started the process.
Turned the machines fuel pressure down until it limped. When it would smooth out I lowered the fuel pressure again & again.
The BG distribution outlet’s salesman tried for almost two years to find out why my washes were better than other shops.
Our old TV commercials showed my mom in her STS before & after boiling the hides.
BG sells a great decloaking spray that you can invert the can.
Cleans Mass air flow sensors & the small hole on the butterfly along with upstream & downstream 02 sensors.

If you do this, do it BEFORE you change the oil.
Plus change the oil right after you are done as a carbon filled oil pan causes etching.

If done this way you don’t even need to add BG’s 44k tank additive.

Seen new oil look old after the process.

Conical injector pattern without breaks pushes the piston evenly.

Sea Foam is #2

I am changing the oil & filter at 1000 miles tomorrow for break in.

Sold out in 2000 so I only work on my own now.?

So.. you cleaned the injectors at 1k miles? I must be missing something

 

[GoVR46]

Is that a magnet mount......

https://www.amazon.com/gp/aw/d/B07RZZVY67?psc=1&ref=ppx_pop_mob_b_asin_title

 

[GoVR46]

I'm sorry. Still lost. What did you install? For us slow folks please.

Magnet mount for firearm.

 

[TheSolarWizard]

Molle panel to carry tools and jack.

Which bed mat is this?

 

[sblaine]

Bought a Mojave steering wheel and installed it tonight in my Sport S. I love the shape of the wheel and the perforated leather. Pretty simple install. I thought it turned out nice.

 

[TheSolarWizard]

Bought a Mojave steering wheel and installed it tonight in my Sport S. I love the shape of the wheel and the perforated leather. Pretty simple install. I thought it turned out nice.

Got a part number? How hard was this to do?

 

[sblaine]

Got a part number? How hard was this to do?

Oh dang. Didn’t think about getting a part number before I installed. Bought from a salvage yard.

It was easy. Just make sure you disconnect both batteries and wait about 20 mins. Just need to make sure and be safe when dealing with airbag. Took me about 10-15 mins.

Sponsored