What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Sarge502]

Finished adding the Rubi take offs to the rear. Even threw on some black lug nuts

Sponsored

 

[TheJoyceIsYours]

How does the receiver bolt onto the stock hitch? I've been trying to figure out if I can install the mopar receiver without removing the bumper.

From the looks of it, I think you might be able to install it without removing the bumper. The only two bolts that I see I believe have access behind the license plate. There's a couple of pics. It looks like all the other hardware far out on the two sides you should be able to get to it. I can't say for sure it'll be fun, but I think it's doable

 

[AlbizzleFoShizzle]

1.5" spacer installed today for the front, .75" on the way, maybe get to install that next weekend. Should have taken some pictures of the process, but didn't. Was able to install without removing the track bar. No noticable offset with the front axle and the steering wheel didn't have to be adjusted.

I don’t know if you’re in the market for some but I’m selling my rubicon suspension take offs. If you’re interested…

 

[be77solo]

Not necessarily all today, but here goes:

Rock Hard Sliders
Rubi rims
Kenda Klever 35x10.5
Yakima Overhaul w/ 1up side mounted bike rack (off of last JT)
RedArc brake controller
Center console organizer
Plasti Dip - front bumper bezels, trail rated badge , and keyholes
New tailgate badge - limitlessparts.com

Great looking tires, you liking them? Been eyeballing them a while myself....

 

[NewGladdyOWNR]

 

[Vtac2]

Picked up my 37 spare. Didn’t try it aired up fully, currently sitting at 15lbs. All snuggled in under the bed. ?

 

[Tank Concrete]

I cleaned bugs off of the windshield today.

I don't believe this at all. Not possible.

 

[Jeep-A-Kneez]

I don’t know if you’re in the market for some but I’m selling my rubicon suspension take offs. If you’re interested…

Hey, thanks for letting me know. I have been kicking the idea of upgrading the shocks, just haven't decided yet.

 

[Tank Concrete]

That's a great sticker! Would be a great spot to sneak in a tiny Jeep on the peak!

 

[IamAlan]

Any pointers? I have the stuff for this, minus the bezel, and was looking to do it soon.
Also…got a p/n for the bezel?

When I replaced my bumper, I found the OEM removal to be quite easy. Note: the 16MM socket needs to be a deep well.
https://www.addictivedesertdesigns....ter-Rear-Bumper-Installation-Instructions.pdf

 

[TheScott]

Installed a Bak x4S tonneau. Unfortunately it arrived missing all the hardware, but I was able to buy some and install it anyway. Other than that, I am really happy with it.

 

[SelfmodJT]

Not really for the gladiator, but its staying in the gladiator. I hope this burner is good as the reviews because this was not cheap. Anyone use or have this? Please let me know if it sucks so I can return it, lol.

 

[AJ-MJ]

I finished up my last project today. I installed the Metal Cloak stabilizer relocation kit. Previously, I installed the Metal Cloak front axle disconnect skid plate , the Rusty's lower control arm skid plates and the Rock Hard lower control arm skid plates. I also installed the Asfir engine and transfer skid plates. On to the next project: install my ham radio and antenna. MORE FUN AND MORE MONEY!!!

 

[mojavegraygladiator]

@ORACLElights

sidetrack ambient and turn signal

 

[USMC-SSGT]

New shoes and some rokblox. While I really wanted a deeper dish (they were available in a -24) sometimes being practical and legal needs to take precedence over a look. These are +10 and still stick out 2+ inches past the fender.

Sponsored