Anyone have the Daystar 3/4” level kit or just the 1” Teraflex puck installed?

[Phishs]

Looking for pics of a JT with using just the Daystar 3/4” level kit in the front or using the 1” Teraflex puck. Prefer on a Rubi but any pics would help. I’m not wanting to go the whole 1.5” so trying to see what these options would look like on my Jeep.

Sponsored

 

[Courtsm3]

My previous 20’ gasser had the 1.5” teraflex and an additional .5” spacer. The 1.5” comes with 1” plus the .5”. Just get that kit and keep the .5”, you might want it down the road. Personally the .75” doesnt look much different over stock. I just added the 1.5” to my new 21’ diesel today.

 

[Phishs]

My previous 20’ gasser had the 1.5” teraflex and an additional .5” spacer. The 1.5” comes with 1” plus the .5”. Just get that kit and keep the .5”, you might want it down the road. Personally the .75” doesnt look much different over stock. I just added the 1.5” to my new 21’ diesel today.

Thanks! I’ve seen a lot of people using the 1.5 in the front and 3/4 in the rear for a total of 3/4 extra in the front. Just wondering how that might look without doing the rear. I’d like to keep a little rake.

 

[Courtsm3]

Thanks! I’ve seen a lot of people using the 1.5 in the front and 3/4 in the rear for a total of 3/4 extra in the front. Just wondering how that might look without doing the rear. I’d like to keep a little rake.

I have just over 1” rake in the rear still. When I did the 1.5” f and .75” rear on my 20”, it was about 1.5-1.75” rear rake.

 

[HookemNC]

Looking for pics of a JT with using just the Daystar 3/4” level kit in the front or using the 1” Teraflex puck. Prefer on a Rubi but any pics would help. I’m not wanting to go the whole 1.5” so trying to see what these options would look like on my Jeep.

I used the 1 inch out of the teraflex 1.5 kit on my JT with the mopar lift. Tiny bit of take left. I didn't add any spacers in the rear.

 

[jeepdan]

Not a good photo.
I just installed Teraflex 1" pucks from a 1 1/2" leveling kit into the front of mine. Weight of the ARB Bumper sagged the front about 1/4". So with the 1" pucks installed, I'm at 36.5" center of front Wheel opening, 37.5" at rear. I pull a trailer so I don't want the front any higher.

 

[Phishs]

Not a good photo.
I just installed Teraflex 1" pucks from a 1 1/2" leveling kit into the front of mine. Weight of the ARB Bumper sagged the front about 1/4". So with the 1" pucks installed, I'm at 36.5" center of front Wheel opening, 37.5" at rear. I pull a trailer so I don't want the front any higher.

That’s pretty much the measurements I’m looking for. Love that Jeep in the back.

 

[Phishs]

I have the Daystar .75” spacers on the front with Rubi take-off springs. Also jammed .75” Daystar spacers under my stock Mac’s toe rear springs.
Tires are 285/75/17 for reference.

Sits perfect. So you have 3/4” in the front and rear?

 

[Garemlin]

Teraflex 1" spacer with Rubicon front springs and max tow rear springs. The last pic is in comparison to a stock Mojave.

 

[Rocksalt]

3/4" front spacer only

 

[Phishs]

3/4" front spacer only

Which spacer did you use? Happy with the results?

 

[jeepstertim]

Thanks! I’ve seen a lot of people using the 1.5 in the front and 3/4 in the rear for a total of 3/4 extra in the front. Just wondering how that might look without doing the rear. I’d like to keep a little rake.

I did exactly that, happy.

 

[Phishs]

I did exactly that, happy.

Which 3/4” kit did you use?

 

[jeepstertim]

Which 3/4” kit did you use?

Daystar, bit a of a battle to fit it, not much movement when dropping the rear axle.

 

[Browning]

Top pic (at the barn) is with 1.5 terraflex front spacer. Bottom pic is just the 1". Still have some rake with the 1.5" as I have steel factory bumper and winch up front. No rear spacer.

Sponsored