What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[BigC1066]

New 813fabrication under reseat lockable Molle storage with ARB tank, filled by an ARB twin mounted behind rear driver seat.
JCR Molle center console addedto both sides (had to change up the hardware for install, suppled screws not good enough) added a mag mount gun mag, an iFAK, and my new SoG trauma shears.
Then went back to the storage to add a few quickfists to hold throwing axe (for now) and Element fire extinguisher.

Sponsored

 

[redriderjf87]

Installed my mesh shades today, of course hitting another cold spell so won't be seeing the top come off for a bit..

 

[Trauma PA]

Don’t throw out your old ones. Ive seen posts on here, and the JL forums, where the metal clamps rust oddly fast. Some in less than a month. Not sure about your brand specifically bur id keep the OEMs as backup

Appreciate the tip but did you see what the squirrels did to my OEM ONES?
I installed the same metal hood latches that I installed on my daughter’s JK. Going on 2 years and fingers crossed, no rust.

 

[sass JT]

No...like rock sliders or something different? Their quality is top-notch.

Check out this thread. They are frame skids for the control arms

https://www.jeepgladiatorforum.com/forum/threads/rockhard-f-r-frame-side-control-arm-skids.57676/

 

[DenverBob]

Check out this thread. They are frame skids for the control arms

https://www.jeepgladiatorforum.com/forum/threads/rockhard-f-r-frame-side-control-arm-skids.57676/

Thanks, I may add those to the list. I just ordered Rancho and DV8 dif skid plates. Would have preferred Rancho for both but they currently don’t have front dif skid for 22 JT.

 

[Fouts]

New 813fabrication under reseat lockable Molle storage with ARB tank, filled by an ARB twin mounted behind rear driver seat.
JCR Molle center console addedto both sides (had to change up the hardware for install, suppled screws not good enough) added a mag mount gun mag, an iFAK, and my new SoG trauma shears.
Then went back to the storage to add a few quickfists to hold throwing axe (for now) and Element fire extinguisher.

very nice setup. Is there a best way to attach quick fist to molle panel?

 

[BigC1066]

very nice setup. Is there a best way to attach quick fist to molle panel?

Well don’t know about best way, but I used a 1 1/4x#8 screw head bolt with 1 1/4 fender washer with lock nut. Then just made sure to not over tighten to much due to the rubber.

 

[Hootbro]

New 813fabrication under reseat lockable Molle storage with ARB tank, filled by an ARB twin mounted behind rear driver seat.
JCR Molle center console addedto both sides (had to change up the hardware for install, suppled screws not good enough) added a mag mount gun mag, an iFAK, and my new SoG trauma shears.
Then went back to the storage to add a few quickfists to hold throwing axe (for now) and Element fire extinguisher.

Do the rear floor mats still come out easily?

 

[BLK HOLE]

Do the rear floor mats still come out easily?

Yes. They tuck just under the unit.

 

[RSK]

Got a bunch done today around the house snd a bit done on tge jeep

Fishbone foot rests
Tuffy console locker
Fully naked for the first time this year
Took some measurement to see how much clearance I have to go bigger on tires. 38” or a small 40” will fit I am betting.

Which hoist system are you using?

 

[FLUndertaker]

Which hoist system are you using?

Self made. Unistrut mounted to the ceiling. Couple of Amazon sourced trolleys with a HF electric hoist bolted on. 6’ sigh post with webbing and grommets. Couple of hitch pins to lift from factory bolt holes. Makes removal a 1 man 5 minute job and holds my top up and out of the way all summer.

 

[RCKLNDR]

Reworked my DIY rack the weekend. I originally made it 90 degrees so my trifold tonneau could flip but that left it looking “off” now that I run the Softopper.

 

[XraytecH]

Installed a set of MOPAR XTREME!!! Recon fender flare extenders on my Sport S.

https://www.allmoparparts.com/sku/jlreconflareext.html

To get these to fit, I had to drill 8 holes in each the fender trim and some bending to get these pop riveted.

If you need to get rig legal cuz your tires stick out a little, these may be a good option for Sport S and Rubicon owners.

 

[DenverBob]

JCR Offroad, bedsides molle panels purchased from a forum member. Great quality and easy install using the cargo rail screws. Perfect place for the hi-lift jack gear and E50 fire extinguisher.

 

[Garemlin]

@Urban Jeep Outfitters tailgate badge

Sponsored