jac04
Well-Known Member
- Thread starter
- #1
2021 JT Mojave, 3.6 gas, AT, 45900 miles, no drivetrain or steering system modifications.
Yesterday I had a scary experience on the highway when my electric power steering (EPS) stopped working. The JT was completely up to temperature, had been cruising at about 70-73mph, and all of a sudden I felt a slight 'tug' at the steering wheel and noticed the power steering was no longer working. Now, immediately before the EPS shut off, I went WOT for about 2-3 seconds to avoid snow coming off the top of a semi trailer, then took my foot off the gas pedal, and a second or so after that is when I felt the 'tug'.
Initially I thought I had a tire blowout, but I immediately checked tire pressure and everything was OK. Then I checked voltage, which was also normal at 14.6-14.7V (which is in range for where the voltage has always been).
I can tell you that this vehicle is VERY difficult to steer without EPS, even on the highway with minimal steering inputs required. If one of my kids or my wife was driving, this could have ended very badly.
I was able to fight the steering to take an exit, and as soon as I slowed down to about 20mph to make a right turn into a parking area, the EPS started working again. I stopped and did a cursory under-hood check at idle, but noticed nothing unusual.
The rest of my trip was uneventful. Drove another 75 highway miles, shut off for about 30-40 minutes, then drove about 150 highway miles back home. I brought my son to school this morning, no issues.
I scanned for DTCs as soon as I got home yesterday and there were no codes at all. Here is the screen showing the steering modules:
- Battery terminals & connections checked OK.
- Fuses were all seated.
- Checked the EPS connector up near the air filter and everything seems fine, although I did not disconnect it to look inside.
- Checked all the connections at the high-amp "N" fuse array. The only nut I could snug up on just a little bit was the N6 connection, which is for the Electric Power Steering Pump. It definitely wasn't loose, it just wasn't as tight as the others. Coincidence? Maybe.
The EPS isn't covered under the drivetrain warranty, and there are no codes showing, so I doubt the dealer could do anything other than charge me a diagnostic fee to tell me everything is OK.
I wonder if this is something that I should report to the NHTSA.
So, has anyone else had an experience like this?
Yesterday I had a scary experience on the highway when my electric power steering (EPS) stopped working. The JT was completely up to temperature, had been cruising at about 70-73mph, and all of a sudden I felt a slight 'tug' at the steering wheel and noticed the power steering was no longer working. Now, immediately before the EPS shut off, I went WOT for about 2-3 seconds to avoid snow coming off the top of a semi trailer, then took my foot off the gas pedal, and a second or so after that is when I felt the 'tug'.
Initially I thought I had a tire blowout, but I immediately checked tire pressure and everything was OK. Then I checked voltage, which was also normal at 14.6-14.7V (which is in range for where the voltage has always been).
I can tell you that this vehicle is VERY difficult to steer without EPS, even on the highway with minimal steering inputs required. If one of my kids or my wife was driving, this could have ended very badly.
I was able to fight the steering to take an exit, and as soon as I slowed down to about 20mph to make a right turn into a parking area, the EPS started working again. I stopped and did a cursory under-hood check at idle, but noticed nothing unusual.
The rest of my trip was uneventful. Drove another 75 highway miles, shut off for about 30-40 minutes, then drove about 150 highway miles back home. I brought my son to school this morning, no issues.
I scanned for DTCs as soon as I got home yesterday and there were no codes at all. Here is the screen showing the steering modules:
- Battery terminals & connections checked OK.
- Fuses were all seated.
- Checked the EPS connector up near the air filter and everything seems fine, although I did not disconnect it to look inside.
- Checked all the connections at the high-amp "N" fuse array. The only nut I could snug up on just a little bit was the N6 connection, which is for the Electric Power Steering Pump. It definitely wasn't loose, it just wasn't as tight as the others. Coincidence? Maybe.
The EPS isn't covered under the drivetrain warranty, and there are no codes showing, so I doubt the dealer could do anything other than charge me a diagnostic fee to tell me everything is OK.
I wonder if this is something that I should report to the NHTSA.
So, has anyone else had an experience like this?
Sponsored
