What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[DAVECS1]

I had to adjust three of the latches, but it was pretty easy, after that no door rattle.The hinges on these look better than my stock ones.

Sponsored

 

[TheHops]

I finally installed my old compressor with an Innovative JK Products kit.

Fairly straightforward install. No regrets!

 

[LiftedLife]

Ordered mine earlier today.

Awesome brother!

Just installed winch and sway bar disconnects

Check out pics!

 

[KDR83]

what do you think about em? Do they adjust well to prevent rattle? I've been eyeballing them mainly so I can ride doorless and not worry about kids/dogs.

Yup no issues with rattles, so far they meet expectations

 

[Mark Doiron]

Received the Carolina Metal Masters grab handle Ram-ball adapter and used it to mount my Nexus 7 on a TabTite mount. This replaced the prior windshield suction cup mount. Need to take for a test drive to ensure the GPS receives a good signal at its new location. Thank you whomever shared this earlier--it's a great solution.

 

[JWest]

Awesome brother!

Just installed winch and sway bar disconnects

Check out pics!

Awesome set up!

So what’s next on your list?

 

[dwayneturner70]

I installed the Vision-X back-up lights.

How did you disassemble the rear bumper to install those? Did you have to remove the bumper? is the tow hitch attached?

 

[MACulberson]

Looks nice. Looks like you are plugged into trailer plug to power the lights?

Yes. It's a temporary fix until I can find out which wire in the tail lamp assembly is the reverse wire. I want my lights to come on automatically when I shift to reverse.

 

[MACulberson]

How did you disassemble the rear bumper to install those? Did you have to remove the bumper? is the tow hitch attached?

There are three 7mm bolts holding each reflector and they're not really that hard to get to. Bumper stays on. Yes, I have a hitch on my truck.

 

[@californiajeeping]

Got it home and threw the 35s on it. Max tow with no lift and bfg ko2 fit perfect. Removed the winglet thingies and it fits goood. Looks factory

 

[kajunkahuna]

Added N-Fab steps, Badlands winch, window shades, and latch on cover to slow down someone from borrowing anything in the bed.

 

[kosmos]

Finished up a custom HAM Radio Bracket for the Builtright Gladiator rail kit.
This will be used to hold a Yaesu ATAS-120 HF antenna - will get that installed later.

Used 3 X 3 X 1/4" Stainless steel angle - this will not flex or move. Really good solid mount for a big HF mobile antenna.

Stainless Steel 3X3X1/4" Angle Bracket

Antenna Bracket and Antenna Mount


HAM Radio Antenna Mount
​

More photos in the gallery.

 

[capercrew02]

Great install! Perfect for heavy antennas like you mentioned, I did a lightweight install on the cowling for my dual bander.

Finished up a custom HAM Radio Bracket for the Builtright Gladiator rail kit.
This will be used to hold a Yaesu ATAS-120 HF antenna - will get that installed later.

Used 3 X 3 X 1/4" Stainless steel angle - this will not flex or move. Really good solid mount for a big HF mobile antenna.

Stainless Steel 3X3X1/4" Angle Bracket

Antenna Bracket and Antenna Mount


HAM Radio Antenna Mount
​

More photos in the gallery.

 

[Texops]

Installed Mopar cowel light mounts & 4” 360 rigid spots, & fog lights on the front bumper.
Also my portable ARB twin is now onboard under passenger seat. Waiting on a few fittings to install my air up down system for each wheel well

 

[@californiajeeping]

Got a set of Rubicon sliders for 100$ with hardware at WFO CONCEPTS here in Auburn.

Exactly what I needed. Working on finding a set of Rubicon fox shocks. Got a spacer lift coming need a bed mat. All the basics.

Sponsored