What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[Strider62]

Just doing the air feeds for the on-board air and few asked how the KC eras looked like a bit back so here ya go

Cheers, mate!

Sponsored

 

[wiredup60]

Thanks!

It's not custom; it's the Truck Covers USA tonneau with Yakima rails installed from factory and Yakima rack installed on it. RTT is then mounted to the Yakima rack.

Nice looking truck! What roof rack is that?

 

[johnparjr]

Nice looking truck! What roof rack is that?

Re Read his post he says what it is twice

 

[johnparjr]

Have gone back 4 pages and hadn't seen it. Was just hoping for a quick answer.

Yakima

 

[wiredup60]

Re Read his post he says what it is twice

I don't think the actual roof rack he has is Yakima. What he mounted the roof rack tent to, on his bed, is yakima. That post wasn't discussing the actual rack on his roof. That's why I was confused. Looks like the JCR rack.

 

[brain]

I don't think the actual roof rack he has is Yakima. What he mounted the roof rack tent to, on his bed, is yakima. That post wasn't discussing the actual rack on his roof. That's why I was confused. Looks like the JCR rack.

“Rack” is the frame mounted in the truck bed. The “basket” sits on top of the rack.

 

[MoparToYou]

I had 37s put on my Mo Jave today. Sorry for the cramped garage photo, it was dark:30 outside before I got home from work.

 

[DrJ]

Nice looking truck! What roof rack is that?

Thanks! JCR 1/2 rack to work with the Bestop Sunrider

 

[Commodus]

I had 37s put on my Mo Jave today. Sorry for the cramped garage photo, it was dark:30 outside before I got home from work.

Looks good, and at least your Mojave fits in your garage.

 

[brain]

I had 37s put on my Mo Jave today. Sorry for the cramped garage photo, it was dark:30 outside before I got home from work.

Looking BURLY and STRONG.

I went with the black plastic fenders as well. I feel they add a bit of utility attitude.

 

[mx5red]

Yes it’s under a Bestop tonneau.

Thank you..
I just looked back at your prior post. Been looking for fridges to fit under mine!
"It’s the older model CFX35.
Yep fits under the tonneau cover with no issues. "

 

[mx5red]

Nicely done. I also like how you have the RTT mounted quite lower than most that I have seen. Is that custom mounting?

As DrJ replied.. His postings have been very helpful.

https://www.jeepgladiatorforum.com/...ver-rolling-tonneau-install-and-review.33134/
Yakima Landing Pad (#1 I believe) fits in the t-slot on the Bak x4/Truck Covers, then their Skyline mount, then rails.

Or can add Tonneau Kit 1 pads, then Overhaul/Outpost towers, then rails.

 

[Bama_Swampfox]

I have the Mopar hard, folding tonneau cover and had a hard time finding a cooler to fit below the cover. I ended up with a Dometic CC32.

The only caveat is that the cooler needs to sit sideways to fit between the tonneau panel braces. It fits perfectly sideways next to the tailgate and easy to get at by just opening the rearmost tonneau panel.

The tonneau panel braces end up keeping the cooler relatively in place.

Thank you..
I just looked back at your prior post. Been looking for fridges to fit under mine!
"It’s the older model CFX35.
Yep fits under the tonneau cover with no issues. "

 

[CWGrisw0ld]

Clayton 3.5” Overland Plus, 37s, Black Rhino wheels, and RSE sliders

 

[Alans17]

Installed my Simple Aux this morning. I didn’t fully seat wire #3 before I crimped so I’ll need to redo that at some point or just bypass the Simple Aux altogether. It doesn’t have a planned assignment so I’m not freaking out about it.

Sponsored