What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[MJRSC]

Busy last couple of weeks…
Added:
Rubicon Performance rock sliders
2” AEV lift
37x12.5 BFG KO2’s
AEV Salta XR’s

And thanks to Black Friday, en route are some Diode Dynamics Stage Series 6” LED bars, Go Rhino cowl mounts, a Lasfit AUX switch bank, and in my cart… Oracle prerunner lights.

Sponsored

 

[ajr2025]

I picked up an ARE CX top today.

 

[KoBear]

prepping for the new bumper/winch.

 

[NorthState*EarthRoamer]

All the wiring and shutoff switch for the winch.

 

[mdyucca]

Re-wired the swaybar disconnect from a rocker to the mopar aux switch. Used high temp abrasive harness tape to matches.

Is this switch operating a Rubicon electronic swaybar actuator?

 

[Vtur]

Is this switch operating a Rubicon electronic swaybar actuator?

Yes.

 

[mdyucca]

Yes.

I would like to see how you have this wired. Can you provide some info/schematic on how you were able to do this?

 

[Vtur]

I would like to see how you have this wired. Can you provide some info/schematic on how you were able to do this?
[/QUOTE

I can sketch up a diagram for you tomorrow. The wiring is the easy part. It requires eliminating the factory actuator control board. Incorporating a N/O switch (arcade), a rod (motorcycle spoke) to activate the switch. See photos for what's involved.

It's a fun and rewarding project if you're into tinkering. Best part is that it stay disconnected at any speed.

 

[mdyucca]

I can sketch up a diagram for you tomorrow. The wiring is the easy part. It requires eliminating the factory actuator control board. Incorporating a N/O switch (arcade), a rod (motorcycle spoke) to activate the switch. See photos for what's involved.

It's a fun and rewarding project if you're into tinkering. Best part is that it stay disconnected at any speed.

I’d like to take a look at it and see how you went about it. Thanks

 

[jebiruph]

I'm not sure but the struts are labeled DeeDee so I'd guess that's the box builder too.

DeeZee

 

[Darkamek]

Quadratec stealth light bar
Entry guards
Stubby antenna

 

[Rockabillyroy]

I can sketch up a diagram for you tomorrow. The wiring is the easy part. It requires eliminating the factory actuator control board. Incorporating a N/O switch (arcade), a rod (motorcycle spoke) to activate the switch. See photos for what's involved.

It's a fun and rewarding project if you're into tinkering. Best part is that it stay disconnected at any speed.

I could see a small market for these by those that have bought take offs.

Probably not worth time and effort, but I would have considered buying this over the no limit manual when I had mine.

Anyways, great job. Looks awesome!

 

[chorky]

Well havent really done much to the jeep lately. With cold temps, and no garage, projects will wait for spring most likely. So some things are piling up. Like skid plates, dead pedal, electrical bracket from 813, and relocation bracket for switch pros.

so…instead I have spent the last week installing this.

obviously its not yet finished. Like the duct work. But it is functional and working. I might have to modify it though as Im not super happy with how the draft inducer and blower motor operate. But its going to be my primary heat source when home saving $$$$$ on propane. And, it was $2,000 cheaper than a new propane furnace!

ilI like it. And had to get it before the terrible EPA puts an end to wood burning entirely. Might need to buy a second one and put in storage just for the future!

 

[Vtur]

I could see a small market for these by those that have bought take offs.

Probably not worth time and effort, but I would have considered buying this over the no limit manual when I had mine.

Anyways, great job. Looks awesome!

I agreed. Thanks

 

[trust]

DeeZee

Yup. What he says.... Dee Zee

Sponsored