What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[FLGladiator]

JTops mesh top and CMM mirrors

Those speakers look awesome. What kit did you use?

Sponsored

 

[Mopar King]

Canadian it was $1890 and converted over that’s around $1400 USD. I got the highest end service which is their “Gold” package. I was going to get their Silver package which probably would have been fine at $900 USD. My neighbour has a friend with a detailing business and his cost would have been much cheaper, but since the dealership was paying for 12 hours of labour for paint correction, I decided to go with these guys as well, their reviews for detailing were excellent. That said...the above prices are before paint correction. Originally the quote I got over the phone was around $300 for paint correction as my JT was new and never washed. Little did I know about the damage done to it by the dealership detailers they were originally using...Paint correction was billed to the dealership at $700 USD which they took care of for me.

It can be done DIY but I don’t have any of the skills or patience to do a proper paint correction. Everything I’ve researched is if the paint is properly polished and prepped the better the outcome. If the preparation of your paint isn’t done right, the ceramic coating will just lock in the swirls and imperfections.

Thanks for the info!!

 

[htremper]

Installed 4 traction boards under my RTT.

You clever clever b*stard!!! I am stealing that move tomorrow morning.

thank you

 

[DocMike]

Ordered my Rock Hard sliders with angled up steps and picked up a set of Rubicon springs and shocks. Install on all parts soon. Hopefully the delivery for the sliders will not take too long.

 

[TRI-JAB]

Just starting my "mild" Jeep project list. Mostly cosmetic upgrades (sill guards, console covers). The next couple of days will be the more substantial upgrades. Yesterday was task 1-3 of 7:
DONE PRO- 1. Install Rhino raptor bed liner (THANKS to the team over @ Axleboy Offroad)!!
DONE DIY - 1A. Install 115V weather proof "pigtail" outlet with Kydex cover (you'll see why in task 5)
DONE DIY - 2. Install Oracle auxiliary LED bed lighting (tie into existing bed lights)
3. DIY Install ZROADZ mini 3" LED floods.
4. DIY install JCR Offroad Overhead MOLLE Panel (along with BTECH 25x4 VHF/UHF Radio)
5. DIY install DECKED full bed cargo management system
6. DIY install JCR Offroad FULL height bed rack (and run VHF-UHF antenna cable)
7. DIY install ROTOPAX mounts.

Hope you enjoy

I just ordered a set of the Oracle Bed lights. Mind sharing any issues you had tying them into the existing rear bed lights? Thanks!

 

[DirkG]

Installed black antenna...31" inch replacement...didn't take a pic, so stock photo below...

 

[hjdca]

Metalcloaked the front diff last night. Bowling balls on both ends now.

 

[BLK HOLE]

ARB mount. Still waiting on my remote coupling hardware and hose so this coupling location will do for now.

 

[Seansmd]

Dipped my toe in the water, only went in a couple of miles, stock Rubicon.

 

[Shootist]

Between Sunday and today I installed hotheads headliners, added 3 decals (have two more to do) and installed my tonneau cover. Here are the decals so far.

 

[LostWoods]

Mopar LED headlight install. It's just not even close how much clarity these lights add without being stupid bright like Toyota and Mazda can be. Sincerely recommend if you don't mind the 2-3 month backorder.

 

[JWest]

I feel like I get a new project done everyday now haha...

1) Installed JCR 1/2 rack.

2) Mounted another ARB connect under the bumper from the compressor in the bed, may change locations pending skid plate decision...

if you don’t mind, whats the height of the half rack from the roof?

 

[DrJ]

if you don’t mind, whats the height of the half rack from the roof?

I got anywhere from 3-3/8” to 4” depending on where on the roof I measure as it isn’t perfectly flat. Highest point is rear the corners of the rack and they sit 4” above but the roof has a bit of a slope at that point.

 

[Gatorgladiatorcanuck]

Installed my rear RokBlokz! It started pouring rain when I got to the fronts, job for tomorrow looks like. I'm really happy with them. The brackets the rear flaps instal with are really heavey duty and look well made. I had to back off the nut and bolt on both sides to get my OEM bolt through the top hole, not sure of its designed that way or not. Was absolutely nothing to do it. They look sharp and will offer some protection I desperately need. After towing a small trailer with 2 kayaks on it 200km (125miles) on gravel, I have 50-60 small chips in the paint on my tailgate. Not sure whats next sill gaurds probably and a 3m clear wrap for additional protection.

 

[DrJ]

Installed my rear RokBlokz! It started pouring rain when I got to the fronts, job for tomorrow looks like. I'm really happy with them. The brackets the rear flaps instal with are really heavey duty and look well made. I had to back off the nut and bolt on both sides to get my OEM bolt through the top hole, not sure of its designed that way or not. Was absolutely nothing to do it. They look sharp and will offer some protection I desperately need. After towing a small trailer with 2 kayaks on it 200km (125miles) on gravel, I have 50-60 small chips in the paint on my tailgate. Not sure whats next sill gaurds probably and a 3m clear wrap for additional protection.

What size did you go with?

Sponsored