What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS]

[irrelevantgoals]

Today I put one thousand nine hundred forty one miles on my Gladiator

Sponsored

 

[Deleted member 30519]

Ordered some recovery boards for my cargo rack to match my silver paint.

 

[Eazye]

Finally finished up my power mods, all of my hood and vent decals that match the factory Rubicon decals are installed. The other subdued big HP gain mod, the 30” light bar and pods have been there for a few months.

 

[-miko-]

Finally got the Rubicon shocks and springs installed along with a Teraflex leveling kit. Guess I’ve got a little ways to go to match their shop truck. They’re the local Jeep guru and the truck drives much better after their alignment setup.

 

[Artsifrtsi]

Went as nekkid as I could, was great weather today! I noticed the truck feels smaller opened up like this...

 

[H_pipe]

Put on a set of Rocktrix Rt 105 wheels with 285/70/17 KO2’s
Wheels are +12 offset (5.5” backspace)
As you see it, no lift, no leveling kit.
Max tow, wide Dana axles, 4.10, etc.

 

[Knaisel]

Put 37“ Mickey Thompson Baja Boss tires, Mopar Slotted wheels and Rubicon flares on my stock Max Tow. Putting Mojave front springs on in the morning. So far they don’t rub at all.

 

[LostWoods]

I need to wire up a winch disconnect myself. The EVO 10-S draws over 350 amps at max draw. Have you had, or do you anticipate, any issues with the switch?

Blue Sea does marine so they under-rate the shit out of their stuff. You will have no issues because while those switches are rated 350A continuous, you can run them for like 5 minutes out of the hour at the intermittent rating which is over 500A.

 

[capercrew02]

Are thy worth the money?

I think so, I use it as a clean solution to store my winching, tie down, and offroad recovery gear, and keep it out of the cab. I’ve had it a few months now and it’s still holding up well, but time will tell.

 

[mrgray]

For today, my truck needs a little interior cleaning to get ready for the holidays. Found my wife's earrings that's been missing for months.

 

[mazeppa]

Mounted Element E100 fire extinguisher on driver front seat adjuster bar.

Edit: Again thanks @punk'n for discount the code that now has unfortunately expired from the "Fire extinguishers" thread.

 

[JRobes]

Mounted Element E100 fire extinguisher on driver front seat adjuster bar.

Edit: Again thanks @punk'n for discount the code that now has unfortunately expired from the "Fire extinguishers" thread.

Was looking at ways to mount mine as well, also ordered with the code from that thread. What did you use to clamp around the adjuster bar?

 

[TJDave]

Not too exciting, but I can't wait to try it out.
Previously, I mounted my required dune flag through a hole on the Arcus bumper meant for extra lights. It was a PITA getting my fat fingers under there to put the nut on the flag.
$2 in Uni-strut parts on the factory Trail Rail and problem solved. Not my idea, I stole it from someone else on this forum. The flag ends up almost 2 feet taller to help warn others that I am there. You can also see the Tyger trifold cover mounts for the Trail Rail system that was included in the bed cover, if anyone is interested.

I think the flag mount is my cheapest, and most boring mod yet!

 

[itsdapk]

Yesterday was Rugged Ridge day! 21 Mojave with Rugged Ridge front and rear flares, liners, bumpers and winch! Still need to install the spare tire setup fresh out of Powder coat.
#gemcustompowdercoating
#hamburgers_superchargers
#ruggedridge
#liquidironindustries
#nittotire
#kg1forged
#diodedynamics
#bedrug
#dcslighting
#wilwood
#retroshopllc
#mbrpexhaust














+3


8Judi Martin Coleman, Eric Eldreth and 6 others

 

[kevman65]

Today I installed the Redline Tuning hood struts and brackets.

I loathe hood props, they either get in the way, or get knocked out and a hood comes down on head or hands.

Have used them before on other vehicles and they are a good, solid product.

Coming soon, Bolt hood locking kit and the Mopar locking gas cap.

Sponsored