Teraflex 1.5 Inch Front Leveling Kit

[Reeb65]

Here is a Teraflex using only the 1 inch spacer on the front. Nitto Grappler 35x12.50x17 tires on the Mopar off road wheels.

I have pretty much the same setup as you and getting ready to add a winch. Did you have much sag after the winch was installed? From pics it still looks level.

Sponsored

 

[Sorbs]

Mopar 2”, Terra-Flex 1.5” on 37’s, and 12k winch.

 

[bhbdvm]

I have pretty much the same setup as you and getting ready to add a winch. Did you have much sag after the winch was installed? From pics it still looks level.

Very little rake in my case. I wanted some because I will be putting a canopy and roof top tent on the bed in the near future . Each vehicle is a little different.

 

[Reeb65]

Very little rake in my case. I wanted some because I will be putting a canopy and roof top tent on the bed in the near future . Each vehicle is a little different.

Thanks for the feedback

 

[Snowdogyyz]

I bought the Terraflex for my Overland. Trying to decide- 1” or 1.5”. I don’t want a rear squat look. Putting 285’s on and no additional lift. What do you guys think?

 

[Reasons]

When I added a steel bumper and winch my front end dropped an additional 0.5", which gave me a total of 2" of rake. I installed the 1.5" Teraflex up front and Daystar 0.75" rear spacers to get my rake back to 1.25."

I'm still debating on tires. Most likely I will only go 35s but 37s are so tempting. Will 37s rub at FULL Articulation (Sway bar disconnected) with just a 1.5" lift and 1" bump-stop up front?

 

[Reeb65]

I bought the Terraflex for my Overland. Trying to decide- 1” or 1.5”. I don’t want a rear squat look. Putting 285’s on and no additional lift. What do you guys think?

Based on what i have observed the Overl

I bought the Terraflex for my Overland. Trying to decide- 1” or 1.5”. I don’t want a rear squat look. Putting 285’s on and no additional lift. What do you guys think?

Based on the visual difference between the rubicon and overland i think you will need the full 1.5" to get level.

 

[Deleted member 24880]

I just did the full 1.5” on my sport s. My rear is a tad saggy but I also have 250-300 of weight in the bed for winter. I say do all 1.5”. You can always add a rear spacer if you need to. They are cheap.

 

[12BNNT]

Based on what I’ve read on the forum, I went ahead and ordered the terraflex 1&1/2” spacer lift for my JTR. I kept the Bestop High Rock bumper and 15k winch from the JK to put on here and being as it dropped the front of my JK sport almost an inch I figured I’d need the full 1&1/2”’s. Got the winch and bumper mounted today (along with the led halo headlights and fog lights) and measuring before and after, the JTR only dropped 1/2” in the front. So now the plan is to put the full 1&1/2” in the front and a Daystar 3/4” in the rear. Effectively lifting the back by 3/4” and 1” in the front. (A little more room for the 35’s when off road) yet keeping some rake for towing purposes. Got a 7x16’ cargo camper conversion to pull. With 300lbs tongue weight the back dropped 1&1/2”’s.

 

[Ray Howrad]

I installed the Teraflex kit a couple weeks ago. I just used the 1" spacer. No problems thus far.

Did you bother with the bump stop extensions?

 

[NEWBWHEELER]

Mopar 2”, Terra-Flex 1.5” on 37’s, and 12k winch.

Would you say that the front is a tad higher than the rear? It’s hard to be sure from those angles. I ask because I have the same lift and am about to put on a 10000lbs 10s and I’m debating if I should do the 1” or full 1.5”.

 

[Sorbs]

Would you say that the front is a tad higher than the rear? It’s hard to be sure from those angles. I ask because I have the same lift and am about to put on a 10000lbs 10s and I’m debating if I should do the 1” or full 1.5”.

I’ve a 12k Apex winch in the bumper. It’s level.

 

[Browning]

I installed the 1" spacer only on mine this weekend. Measured to the rock rail from the ground and it's 18 1/2" in the front and 19" in the back after install. I have the factory steel bumper with mopar 7" lights, Light bar, and 9500lb winch. Sitting on 35x12.50 ridge grapplers. For reference for anybody who is thinking of doing this. I also have airbags installed in the rear but no air in them (actually 5lbs) in this pic and for the measurements. Truck sitting on a hill in this pic in front of my office so it's hard tell the rake but it's there.

 

[Rubiman]

Here is a Teraflex using only the 1 inch spacer on the front. Nitto Grappler 35x12.50x17 tires on the Mopar off road wheels.

How does it ride? Interesting it’s still leveled in the front with a winch.

 

[Rubiman]

I installed the 1" spacer only on mine this weekend. Measured to the rock rail from the ground and it's 18 1/2" in the front and 19" in the back after install. I have the factory steel bumper with mopar 7" lights, Light bar, and 9500lb winch. Sitting on 35x12.50 ridge grapplers. For reference for anybody who is thinking of doing this. I also have airbags installed in the rear but no air in them (actually 5lbs) in this pic and for the measurements. Truck sitting on a hill in this pic in front of my office so it's hard tell the rake but it's there.

Looks perfect. What made you only go with the 1”?

Sponsored