What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[SelfmodJT]

I see your point... but, he survived, he got his gun back, and you can buy a new glock while you’re waiting

Lol, he has an arsenal. Hes the one that got me started. He has like 10 backups ?

Sponsored

 

[SelfmodJT]

I see your point... but, he survived, he got his gun back, and you can buy a new glock while you’re waiting

Here's my EDC, dont be a hater lol. Ruger mark iv lite 22lr. I dont need a 9mm? Its my tron gun. It'll look good mounted next to my twin arb compressor, when I eventually get one lol.

 

[Rubi_Rhod]

Here's my EDC, dont be a hater lol. Ruger mark iv lite 22lr. I dont need a 9mm? Its my tron gun. It'll look good mounted next to my twin arb compressor, when I eventually get one lol.

Nice! I love mine.

 

[KurtP]

Love your posts.
I hadn’t heard of Timbren before, these are just rubber, right? I was going to order the Metalcloak ones for $50, are these really $200 different?

Thanks.

I honestly dont know for sure, this will be my first set. From the research ive done, people who use them generally seem to really like them. They reportedly control bump stop travel really well, progressively, and smoothly; while returning the energy in a much more controlled/less springy fashion....almost like a poor man’s hydro stop.

We’ll see. ??‍

 

[Sportsbiz]

Here's my EDC, dont be a hater lol. Ruger mark iv lite 22lr. I dont need a 9mm? Its my tron gun. It'll look good mounted next to my twin arb compressor, when I eventually get one lol.

Those are SOOOOO FUN to shoot.

 

[MadMojave]

Installed Baja Design LP4 lights. The brackets were mounted upside down hanging in the bull bar. This mount is uncommon to see, but this way the lights are pushed forward exactly in the spot I wanted allowing the peripheral light of LP4 spread better without any interference of the bumper. Would be easier mount the lights over the bull bar, but other main advantage to mount this way is the projection of the lights seated in a better spot fulfilling and working together with the headlights and fog lights. What do you think?

 

[GibbyWibby]

what’s the model number of these speakers? And no mods needed? They are a direct fit? Sorry if this is an old topic, I tried to find it in the forums but couldn’t.

These are 100% plug and play to replace the 3.5 tweeters on the soundbar and top dash. Believe me I had been looking for the past 2 months and still cannot find the 4 inch speaker upgrade on the soundbar that is a plug and play https://www.amazon.com/gp/product/B01EXO58MS/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

 

[fyrefight]

Went thru www.mythreedom.com and changed my original key fob out for their mini m fob. The site has recently started taking orders. But it's new and there are not a lot of customizations available yet. This thing is crazy small and works great. I had a second key cut to place under the truck since it is not attached to the fob anymore in case of emergency and the other to leave in the truck so I can lock the places inside if wanted.

I'm still having a hard time justifying $50 for a couple pieces of plastic. Ouch.

 

[eligius]

Got a question regarding front bumper fitment . Will the Fab Fours JK07-B1951-B Front Stubby Bumper from a JK fit the JL/JT model. I know there's a specific bumper for a JL/JT but is more expensive and both bumpers look the same to me. Any thought guys? Links below. Thanks.

https://www.quadratec.com/p/fab-fou...campaign=remarketing&utm_content=lower-funnel

https://www.quadratec.com/p/fab-fours/front-stubby-bumper-jeep-wrangler-jl-gladiator-jt

 

[Blue Ridge]

I feel like us gun guys are taking over the thread so happy to start a new one on the topic if appropriate. But I had to show off the .22 I had built for my wife to match her Kitchenaid appliances.

 

[KurtP]

Installed @ACE Engineering sliders. These things are pure beef, and the up angle makes for a great step and great clearance. Also has plenty enough “kick out” side coverage for my uses. Was nice to find i didnt have to cut up the mudflaps.

Solid product.

 

[Rubi_Rhod]

I made it a flag and got it mounted.

Pro-tip: Work smarter, not harder. Raise the front to bring the back end down to working height.

 

[Unkiebunk045]

got my soft top on; maybe a little early for CT, but i was getting too anxious.

I was able to lift it off myself and lay it on a carpet in my garage. I then rigged a pulley system (3 pulleys to lighten the load) to lift it to my top; once it was high enough i pushed it over to my wall; laid it on the hook and used some cam buckles to keep it secure. I think the overall spend is $40-50.

i was going to have my wife video tape my hoisting it, but deciding against it in case it failed; didn’t want that memory lasting forever.

 

[Gren71]

Added some sealing strips to a couple gaps along the windshield, hopefully it clears up my wind whistle

 

[SelfmodJT]

Installed @ACE Engineering sliders. These things are pure beef, and the up angle makes for a great step and great clearance. Also has plenty enough “kick out” side coverage for my uses. Was nice to find i didnt have to cut up the mudflaps.

Solid product.

Dam, I would have went with these if I knew they would have worked with the factory rock rails.

Sponsored