What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[MDPensFan]

Installed the Oak colored Hotheads Headliners (looks really good with the Saddle seats), JScan adjusted for the bigger tires, and hooked up the iDrive throttle controller.

Sponsored

 

[DailyMoparGuy]

Installed hood latch locks. They’re pretty nice!

 

[MissionMan]

Created a bed divider with honeycomb plastic sheets. Wouldn't be a jeep user if I didn't put in a little extra effort to make it different. Still needs some finishing and a rubber edge, but it's lightweight, under 2kg's/4lb's

 

[antwon412]

Create a bed divider with honeycomb plastic sheets. Wouldn't be a jeep user if I didn't put in a little extra effort to make it different. Still needs some finishing and a rubber edge, but it's lightweight, under 2kg's/4lb's

That is sweet! I’d buy one of those.
For the Gladiator I haven’t even ordered yet ?

 

[MissionMan]

That is sweet! I’d buy one of those.
For the Gladiator I haven’t even ordered yet ?

It was a bit of a learning process. I'd probably make changes if I did it again, but it was a lot more effort than I wanted because I don't have some of the tools required to make like easier like a circular saw.

 

[kevman65]

Today I added the Desert Does It seat jacker.
Have had back issues for years and when driving the JT my right leg would get sore and almost cramp up. Did some creative seat cushion wedges to see if the seat angle was the culprit. After some time I realized the ad hoc seat wedge was making the leg pain go away.

So I ordered the highest Seat Jacker, which is the fixed height one, got them Friday and installed today. It will take a little getting used to the new seat angle but it is definitely the cat's meow.

 

[MyRight]

Installed hood latch locks. They’re pretty nice!

Where did you get those?

 

[cuellar13]

3.5” lift, 37’s, dual steering stabilizer, and pedal commander.

 

[DailyMoparGuy]

Where did you get those?

Amazon actually. They’re cheap but honestly the material is pretty nice on the latch itself. I stuck with the OEM fasteners because I read some people had rust issues with the Sukemichi ones. Easy installation as well.

Link for Gladiator Hood Latch Locks - Amazon

 

[atxatxatx]

Added Warn Winch (Factory Steel Bumper)
Added JCR Off road Overhead MOLLE panel and wired and installed GMRS Radio.

nice job with the wiring on the warn winch, looks very tidy.

I need to redo my one.

 

[FloridaJT6MT]

That is sweet! I’d buy one of those.
For the Gladiator I haven’t even ordered yet ?

Yep, put me down for one too.

 

[The White Rabbit]

Installed bed cover last Friday and didn’t get a chance to take a picture until yesterday. Lake Amistad outside of Del Rio TX

 

[TexasTJ]

Removed the 37s, time to start going back to stock in preparation to sell.

 

[The White Rabbit]

Removed the 37s, time to start going back to stock in preparation to sell.

Sad news my friend.

 

[zxd9]

Finished the electrical wiring for my bed rack lights. Two on each side and one in the rear. Switch selectable to be powered from main battery via an Spod BantamX or a Bluetti EB70 solar generator. Each side can be independently turned on/off. LIghts are KC Hilites C2 LED 20W Flood Beam. I have one more pointing into the bed. Dometic CFX3 55IM gets installed this week. It too will have selectable power source.


First picture is rear light only. Nicely lights up tailgate area too. You can see the Bluetti EB70 too.
Next is one side, then side and rear and then all three sides.

Sponsored