My OEM Front Trail Cam install thread

[DailyDrivenTJ]

..., I may not run my 2 wires (power and farka) through the firewall. was looking at the drivers side and there is a small set of wires entering the the cabin through what appears to be the windshield gap:I

This seems like a good alternative way to run cable into the cab. I need to run whole bunch of wires between engine bay and cab anyways. Keep in mind Fakra connector has some dimensions to it.

Sponsored

 

[Alc]

Things I found out today:
1. the CVPM is obnoxiously large and the design sucks to place it anywhere other than it’s intended place.
2. A custom bracket will need to be made for it because of its design
3. It cannot fit behind the trim on the passengers right kick panel because of lack of suitable attachment points even with a bracket (need at least 2 approximately 9 inches apart) and it’s so freaking big you won’t be able to reattach the plastic trim.
4. It cannot fit behind the glove compartment. On the left side you have heater coils and the right side you have the speaker and airbag. Directly in the middle there are the cabin air filter and fans.

next will be mount under the passenger seat after I make an archaic bracket. This may take a bit more patience…ripping out my entire interior is still a last resort.

 

[Alc]

Okay MOPAR parts gurus, I need some help find a few parts for this install under the seat. When doing a random search I found the below pic for a 2022 Ram (Camera Processor Module - Mopar (56029965AC). What I need is the parts number for #4 and #6 and to a less extent #3. If I can get those parts I think the install under the seat will be a cinch and repeatable for those that follow.

 

[ecidiego]

.

 

[ecidiego]

You might also try to figure out where they put it in the Wrangler

 

[ecidiego]

.

 

[RustyC]

Can anyone tell me where the jumper harness for the washer pump plugs into at the other end?
I’m having trouble tracing the existing harness from the pump back
Thanks!

 

[ecidiego]

.

 

[ecidiego]

oh shit you're in Australia? I am not sure if everything is reversed or just the steering setup and interior!

 

[RustyC]

oh shit you're in Australia? I am not sure if everything is reversed or just the steering setup and interior!

I know, I'm rolling the ice a bit on this one. One benefit so far is I can get to the pump through the front fender easily, and my ECU is on the opposite side of the engine bay, however I'm yet to run the hoses, so fingers crossed they are the same.

Also, where about was the alternative CAN point near the front?

Cheers.

 

[Alc]

Yeah that would be even better to find out where in the wrangler but using my logic and reason (which often doesn’t apply to Chrysler) ours was on the back wall there’s must be in the trunk area of the wrangler.
@ecidiego, I’m utterly amazed how quickly you located those parts! That had used up 2 hours today. If it works, That bracket will help me not reinvent the wheel to create one for a weird design on that module. BAM didn’t have those parts so I couldn’t use them…seems kind of often these days.

 

[RustyC]

It's on the driver fender rail up top...visible. I can take a pic later.

Yep a photo would help a lot, there's a good chance its buried under my 12v install, however Id love to have a rough idea before I start puling things apart.

Thanks

 

[RustyC]

I know, I'm rolling the ice a bit on this one. One benefit so far is I can get to the pump through the front fender easily, and my ECU is on the opposite side of the engine bay, however I'm yet to run the hoses, so fingers crossed they are the same.

Also, where about was the alternative CAN point near the front?

Cheers.

So the hose will reach, which is great, however I can’t for the life of me locate the harness plug for the pump wiring.
It’s driving me a bit crazy
Also, is it the white pump outlet that feeds the camera nozzle?

 

[ecidiego]

.

 

[RustyC]

View attachment 352932

The pump only goes in 1 way, it will be clear as day which nozzle is which.

Ok, mines very different.
The wiring is taped into the main loom just after the motor plug.
Does swapping the two pins in the pump connector on the current loom do the same thing?

Sponsored