What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[HooliganActual]

Where did you get the molle on the inside rear window?

It’s one made for the cab wall in the bed:
https://builtrightind.com/products/2020-jeep-gladiator-bedside-rack-system-front-panel

The dimension fit the back of the cab and since it wasn’t actually made for that purpose, I just fabbed some L brackets that bolt to it and then into the hard top hood down bolts on the back wall.

Sponsored

 

[FreedomWV]

Installed the Rough Country CAI, I do not like all of the noise that kind of drones around 2-3k rpm's. I will be putting back to stock today. Does sound nice at wot but just wish it wasn't so annoyingly loud when just normal driving, it is not a nice sound. I drove it for about two hours last night and did not notice any increase in MPG during my trip. BTW that rubber grommet for the sensor is a pita for anyone else who plans on installing as others have noted.

 

[Killroy Was Here]

Installed the Rough Country CAI, I do not like all of the noise that kind of drones around 2-3k rpm's. I will be putting back to stock today. Does sound nice at wot but just wish it wasn't so annoyingly loud when just normal driving, it is not a nice sound. I drove it for about two hours last night and did not notice any increase in MPG during my trip. BTW that rubber grommet for the sensor is a pita for anyone else who plans on installing as others have noted.

Any type of cold air intake on these trucks will do nothing to improve your gas mileage.
They just make more noise in general.

 

[DFWJEEP]

No issues with the hood leaning back. Over the attachment bolt is about 6 inches. There is quite a bit more over the hole for the light to go into as it is offset. I have a tennis ball between the hood and window as reference for how far back it is.

Thank you as the mount I have now does not allow the hood to lean back without hitting the lights.

 

[Jut60]

I’m wanting to do the same. Where did you find a wheel?

Found the wheel as a single on eBay, but it was months of looking here, fb, Craigslist, eBay before settling. Almost bought a set of four to then just sell the other three.

 

[Oilburner]

315/70/17 BFGs + Mojaves added today.
2022 JT Rubicon Diesel. No lift.
(small front spacer lift very soon - truck is pointed downhill in pic)

 

[Summitsearcher]

Haha, reminds me of the infamous teapot reflection on Ebay (or some other auction site).

My effin eyes! Where’s the bleach.?

 

[Summitsearcher]

Installed Mopar Performance Rock Rails. I bought them off Craigslist for a great deal.

I have those and love them. Great find.

 

[carmigo]

315/70/17 BFGs + Mojaves added today.
2022 JT Rubicon Diesel. No lift.
(small front spacer lift very soon - truck is pointed downhill in pic)

Looks nice! looking forward to seeing the spacers.

 

[RangerG]

Added Tom Woods drive shafts, front and rear. My plan is to add RCV axle shafts and Yukon rear chromolly axle shafts in July.

 

[WILDHOBO]

Fought to replace my fixed length front lower control arms with adjustables. One of them had a bolt seized in the sleeve. It took 4 hours to cut it out. And lots of carbide sawzall blades. Uppers tomorrow.

 

[Rusty PW]

Fought to replace my fixed length front lower control arms with adjustables. One of them had a bolt seized in the sleeve. It took 4 hours to cut it out. And lots of carbide sawzall blades. Uppers tomorrow.

I feel your pain. Had to cut 3 of them on my Power Wagon when I replaced the control arms.

 

[WILDHOBO]

I feel your pain. Had to cut 3 of them on my Power Wagon when I replaced the control arms.

It’s so horrible. Hopefully never again. Famous last words…

 

[rharr]

heat and a air hammer couldn't win?

 

[WILDHOBO]

heat and a air hammer couldn't win?

Air hammer, definitely not. I didn’t want to use the torch if I could avoid it. I’d rather not risk tempering the steel brackets. The sawzall sucked, but didn’t damage anything, other than scratches that I painted over.

Sponsored