What did you do TO your Gladiator today? [ADMIN WARNING: NO POLITICS, NO GUN TALK]

[drewcnit]

Well have a seat and a drink lol, I have a rebel off-road full rack, Mopar Beadlock wheels with “Linda’s sunset” belton spray paint for the rings, 35x12.5 general X3’s, Apex quick disconnects, rough country tube bumper with the lights they include (front), warn evo 10-s winch, currently waiting delivery of the rear bumper, 2 JL tazer minis, a front locker and the hauk off-road snorkel. Debating on the AEV 2” spacer but then I’ll want to upgrade to 37’s with 4.88 gears most likely.

What do you think of the Apex disconnects? Thinking of grabbing some myself..

Sponsored

 

[RamRod]

What do you think of the Apex disconnects? Thinking of grabbing some myself..

Honestly I was skeptical because they’re $500. But, once I got them I noticed how beefy they were, and the install was simple enough. I haven’t tested them more than climbing things around the neighborhood. It’s super awesome to disconnect a thousand times easier versus the old school method.

 

[doc-ketamine]

https://haukoffroad.com/shop-by-product/accessories/dash-plates/

Looks great! But does the airbag come out of that spot? Would that turn into a projectile?

 

[mx5red]

Looks great! But does the airbag come out of that spot? Would that turn into a projectile?

Don’t be such a wuss, it’s not like you’re the one in the passenger seat?‍

 

[Martinnfb]

Installed Mopar flares. Not great, but not terrible

 

[freebird_78]

Here you go…

https://haukoffroad.com/shop-by-product/accessories/dash-plates/

Well, there goes $30 of mine...

Thanks

 

[DrJ]

Made a 2-tire inflation system. Since I have ARB connectors on both front and rear ends, it only made sense, plus it reduces the amount of gear I have to store.

 

[WILDHOBO]

Made a 2-tire inflation system. Since I have ARB connectors on both front and rear ends, it only made sense, plus it reduces the amount of gear I have to store.

Big fan of the air port in the bumper.

 

[Armsbearer]

Threw on a front bumper with a warn winch, just gotta get the rear bumper in and she’s done……Until I get bored next month?

Did you have to do any trimming to fit the OEM skid plate?

 

[RamRod]

Did you have to do any trimming to fit the OEM skid plate?

Nope, fits right up they send one with the bumper but I’ve been too lazy to mock it up and see what it would be like with the one they sent

 

[OVERLORD]

RR Venator, Q 12K winch

 

[TeraFlex]

I just got my new TeraFlex Ball Joints today! Any install advice? Im nervous about installing the axles without messing up the seals! Did the BJ come preadjusted or do I need to adjust them after installing?

Our ball joints are preadjusted and ready to install right out of the box, so no worries there. It's a good idea to pump them full of grease until a bit of grease pushes out around the lip seals.

 

[ospreyfe55]

Our ball joints are preadjusted and ready to install right out of the box, so no worries there. It's a good idea to pump them full of grease until a bit of grease pushes about around the lip seals.

Should I pre grease them before install or after install. Also I fully trust TF and I am fan! There’s lots of hate out there when I posted my excitement on FB, it had me questioning my purchase but like I said you haven’t steered me wrong with any of your products-no pun intended! I will say one complaint so far, there was no sticker in the box!!!! I thought I was buying a sticker and got free ball joints! ?

 

[jkk58]

Recent updates include repurposing my Harken Hoist from my wranglers hardtops to the JT hard top, grab handles from darksidedesign and Rival hood struts.

 

[RCKLNDR]

Replaced the damaged crossbars on my bed rack.

Just finished piecing the rack back together and got it loaded up for a test drive tomorrow.

Sponsored