Flush Mount Tail Lights

[MR GRANITE]

This shouldn't be happening with the JSCAN & you shouldn't need to wait for what we have in the works since you have this.

I would reach out to JSCAN support to help you properly config the JSCAN. Several members here have done this and they have proven to be very helpful.

I have configured like other members have done here with jscan multiple times-this is not a jsan issue. I also have your bumper reverse lights. Drove it to work this morning and was dark. Started up-everything working-all 4 reverse lights on. No warnings. Used turn signals a couple of times on my way to town and everything fine. Got in town and had to stop behind a school bus for about a minute. Sitting still with just lights on and foot on bake and I get turn signal warning and it cleared itself. Drove another couple miles to work and no issues. Hoping with your fix i can get rid of jscan settings. Everything worked fine with stock LED tailights and your bumper lights in place.

Sponsored

 

[MrFahrenheit]

I have configured like other members have done here with jscan multiple times-this is not a jsan issue. I also have your bumper reverse lights. Drove it to work this morning and was dark. Started up-everything working-all 4 reverse lights on. No warnings. Used turn signals a couple of times on my way to town and everything fine. Got in town and had to stop behind a school bus for about a minute. Sitting still with just lights on and foot on bake and I get turn signal warning and it cleared itself. Drove another couple miles to work and no issues. Hoping with your fix i can get rid of jscan settings. Everything worked fine with stock LED tailights and your bumper lights in place.

I ended up breaking down and getting JSCAN. I have a factory LED and you need to do this process to fix the hyper flash and stuff:

Load up JSCAN, go into Adaptions. Go to “Lights Conversion -> US to EURO”

Then find the left and right rear diagnostic settings:

Start with one side, set the value to deactivate then Hit Go. Once you get the confirmation, turn on that blinker until the hyper flash stops.

Then repeat for the other side.

I did not change any other settings than these ones. I left all the tail lamp led things active. They don’t need to be changed for Factory LED trucks.

I have not had any issue since.

 

[cmb396]

Just seeing these and about to order for my JTR with oem led lights. Is everyone having issues, or just non led trucks?
Also, I already have a flashcal. Does anyone know if an issue does occur if flashcal can correct it?
Have these and backup bumper lights in my cart, but want to do some more homework before ordering.
(Discount code too if there is one also, lol)

 

[bryanklay]

i believe i just got the oracle tail light system up and running. i have been having a problem with the Blind side monitoring system as well as the tail lights not working and after some help from Justin at Oracle and some trouble shooting of wires and pins, i got all of it up and running. the problem that I was having was the pins that were in the connector for the bsm sensors were not engaging the pins in the sensors.

 

[Fcmalie]

Just seeing these and about to order for my JTR with oem led lights. Is everyone having issues, or just non led trucks?
Also, I already have a flashcal. Does anyone know if an issue does occur if flashcal can correct it?
Have these and backup bumper lights in my cart, but want to do some more homework before ordering.
(Discount code too if there is one also, lol)

I honestly didn't get the LED package on my Mojave because I already had aftermarket headlights and taillights for way cheaper than the 1300 that they are asking for the package now. It was a steal at 1000, but with better aftermarket options coming out it isn't really worth the markup.

 

[phranican]

Factory LEDs, bit the bullet and bought into the Jscan setup which helped to turn the warning light off. Now after 4 weeks of flawless operation, the blind-spot monitoring has suddenly stopped working. I turned the bsm setting off and on in the Uconnect settings and the side mirror triangles momentarily glow up when I do that.

Any advice?

 

[MR GRANITE]

Factory LEDs, bit the bullet and bought into the Jscan setup which helped to turn the warning light off. Now after 4 weeks of flawless operation, the blind-spot monitoring has suddenly stopped working. I turned the bsm setting off and on in the Uconnect settings and the side mirror triangles momentarily glow up when I do that.

Any advice?

Someone else on here said the connector for bsm wasn’t connected all the way.

 

[bryanklay]

I honestly didn't get the LED package on my Mojave because I already had aftermarket headlights and taillights for way cheaper than the 1300 that they are asking for the package now. It was a steal at 1000, but with better aftermarket options coming out it isn't really worth the markup.

do you have a BSM service message when you turn the vehicle on? this message will be listed in the instrument cluster. if you do, check the bsm connectors at the tail lights to make sure the pins are engaged to the sensors.

 

[Fcmalie]

do you have a BSM service message when you turn the vehicle on? this message will be listed in the instrument cluster. if you do, check the bsm connectors at the tail lights to make sure the pins are engaged to the sensors.

think you replied to the wrong person. No BSM here

 

[phranican]

do you have a BSM service message when you turn the vehicle on? this message will be listed in the instrument cluster. if you do, check the bsm connectors at the tail lights to make sure the pins are engaged to the sensors.

Thanks. I do not have any service messages in the instrument cluster. I also reviewed the uconnect app diagnostic, no alerts. The lights work fine, no hyperblink. Everything worked perfectly for 4 weeks, now the bsm is suddenly out, does not detect on either side of the vehicle. Seems like a programmng or a hardware issue because it worked flawlessly for 4 weeks. I might swap my oems in and see if that fixes it.

 

[bryanklay]

Thanks. I do not have any service messages in the instrument cluster. I also reviewed the uconnect app diagnostic, no alerts. The lights work fine, no hyperblink. Everything worked perfectly for 4 weeks, now the bsm is suddenly out, does not detect on either side of the vehicle. Seems like a programmng or a hardware issue because it worked flawlessly for 4 weeks. I might swap my oems in and see if that fixes it.

that is how i found out my problem was swap out the oems and everything worked so thru the process of elimination i was able to find the pins were the problem.

 

[bryanklay]

think you replied to the wrong person. No BSM here

as Maxwell Smart would say
"sorry about that Chief"

 

[ilovebikes99]

Guys when are you shipping more of these out? For me it was said Mid November. I'm kinda getting to the point of cancelling the order along with all these issues here

 

[ORACLElights]

Guys when are you shipping more of these out? For me it was said Mid November. I'm kinda getting to the point of cancelling the order along with all these issues here

We started shipping more today, about 200x going out!

 

[ilovebikes99]

We started shipping more today, about 200x going out!

Appreciate the reply. I'll hold on for another 2 weeks.

Sponsored