Updated - Gladiator EcoDiesel Bottoming Out Poll 2 - Spring Part Numbers

[Vtur]

I'll run it as is for now and see what happen. Mine has 3.75" clearance between the bump and pad. The lift bump stop can easily be cut shorter and weld it back if needed it.

Sponsored

 

[Dougstdig]

That’s odd. I can only see 1 sticker and it’s on the left (drivers side). 6378AA. It’s not on your list for the drivers side and bottoming out.

 

[am1978]

That’s odd. I can only see 1 sticker and it’s on the left (drivers side). 6378AA. It’s not on your list for the drivers side and bottoming out.

Thanks for posting. I won’t update the poll because it won’t let me go back to edit it I don’t have the part# for the other side. Other people will see this.

 

[Ericshere03]

I'll run it as is for now and see what happen. Mine has 3.75" clearance between the bump and pad. The lift bump stop can easily be cut shorter and weld it back if needed it.

That’s good info, but it looks like you actually you have 4.75”, that rubber bumper compresses into the cup and the metal to metal contact will be the “bump stop” … My wife’s stock 4xe Sahara has 4-1/8” … Just a comparison …

 

[Vtur]

For those with the mopar lift and the truck has an even lifted height between left (driver) and right (pass.) sides. Before i go and swapping it. Can someone confirm which springs part numbers on which sides of the truck is the correct way?
Think i had installed it incorrectly, as both my front/rear passenger side are sitting 0.5" higher than the driver side.

Thanks in advance

 

[am1978]

For those with the mopar lift and the truck has an even lifted height between left (driver) and right (pass.) sides. Before i go and swapping it. Can someone confirm which springs part numbers on which sides of the truck is the correct way?
Think i had installed it incorrectly, as both my front/rear passenger side are sitting 0.5" higher than the driver side.

Thanks in advance

Who added the red handwritten stuff?

 

[Vtur]

Who added the red handwritten stuff?

Just my note on how i installed it.

 

[troymi]

Curious why you didn’t install in locations per the instructions? Did you have another guide?

 

[Vtur]

I don't know. I went by the pic plus part numbers instead. I was under impression that it's was probably a misprint. And compared with this other instructions below:

 

[CerOf]

Just my note on how i installed it.

You should install it how the directions read.

that’s how I installed mine and I don’t have any side higher than the other.

why did you install them on the wrong side?

 

[ShadowsPapa]

For those with the mopar lift and the truck has an even lifted height between left (driver) and right (pass.) sides. Before i go and swapping it. Can someone confirm which springs part numbers on which sides of the truck is the correct way?
Think i had installed it incorrectly, as both my front/rear passenger side are sitting 0.5" higher than the driver side.

Thanks in advance

Rule on the gassers was always higher number on the right side. So if you have an 808 and an 807, the 808 would go on the right.

Rubicon (gas engine) front springs for example - 339 and 340 340 goes on the right.

Appears from the picture of the parts list here that it's the same for these.

 

[CerOf]

I don't know. I went by the pic plus part numbers instead. I was under impression that it's was probably a misprint. And compared with this other instructions below:

Ahh, now I see your issue. I got no answer for ya.

 

[Vtur]

Ahh, now I see your issue. I got no answer for ya.

So you have 147AA left and 148AA on the right sides and it's sitting evenly? Guess i will give it a shot and swap them over.

 

[Vtur]

Rule on the gassers was always higher number on the right side. So if you have an 808 and an 807, the 808 would go on the right.

Rubicon (gas engine) front springs for example - 339 and 340 340 goes on the right.

Appears from the picture of the parts list here that it's the same for these.

This is exactly why i thought it was a misprint. Usually the higher number install on the gas tank side. So i installed 148AA on the left driver side, as the diesel tank is on the left.

 

[CerOf]

So you have 147AA left and 148AA on the right sides and it's sitting evenly? Guess i will give it a shot and swap them over.

My kid took the JT, when they’re back I’ll look and let you know for sure. But I am level.

Sponsored